Laboratorion leukamurskain
 |
 |
 |
Ja tarkoitus ja Sovellettu kenttä
Our Jaw Crushers are ideally suitable for primary and secondary crushing, with well-capacity and high-efficiency, they are widely used for crushing various medium hard rocks and other ore materials whose maximum pressure-withstanding is 2000 kilogram force/cm3 and they are mainly supplied to the departments like Geological coal char、Mine、Metallurgy、Chemical Engineering、Construction Materials etc. And the labs of junior college academies science and research units.
Ensisijaiset eritelmät ja tekniset tiedot
|
Malli |
Tuloaukko |
Tulokoko
|
Lähtökoko |
Kapasiteetti |
Moottori |
|
LZPE60 × 100 |
60 × 100 mm |
≤55 mm |
3 - 10mm |
230 - 400 kg/h |
1,5 kW |
|
LZPE100 × 150 |
100 × 150 mm |
≤100 mm |
6 - 38 mm |
500 - 2000 kg/h |
3kW |
|
LZPE100 × 100 |
100 × 100 mm |
≤80 mm |
3 - 25 mm |
400 - 1800 kg/h |
3kW |
|
LZPE150 × 250 |
150 × 250 mm |
≤125 mm |
10 - 40 mm |
700 - 5000 kg/h |
3kW |
Pää- työing periaatteellinen
The Jaw crusher structure includes Fabricated Body、Swing Jaw、Eccentric Shaft、Jaw Plates、Toggle mechanism etc parts. The electromotor drives eccentric shaft through triangle strap, to make the swing jaw moves in adjusted locus, thereby the materials in the crushing cavity are crushed.
The fabricated body is electricity welded by steel plates, the fixed jaw plates tightened by bolts are fixed in the front of steel housing, which assist in impacting the plates. The side plates are fixed in the steel housing side-wall which in the right-and-left of the crushing cavity, for preventing the wearing and tearing of the steel housing side-wall.
The swing jaw is a cast steel moulding, its face fixes swing jaw plates, top hang on the housing by eccentric shafts and roller bearings, its infrastructure is supported by toggle mechanism and it is scroll touching with the toggle mechanism. Fly wheels and Strap wheels with grooves are fixed in the two sides of the eccentric steel shafts. The steel housing is welded into the machine seat, electric motor sliding-track is fixed in the machine seat with bolts and a outlet drawer is fisted in the outlet, but it can expel products downwards directly without outlet drawer.
Toggle mechanism is connected with supporting bolts byφ9mm pins when the materials in the crushing cavity can not be crushed and the loads are increased suddenly, viz. The pin parts itself rapidly to protect other works from being destroyed. In the end of supporting bolt, there’s a hand wheel, it is used to adjust the outlet width size. The adjusting process is that remove the setscrew first, then circumgyrate the hand wheel, after adjusting, tighten the setscrew again, the connection between pothook and spring at the down most of the swing jaw make the toggle mechanism and swing jaw not to work outside, and they are adjusted by nuts.
Asennusohjeet
Koneen toimitetaan käyttäjille sen jälkeen, kun valmistustehdas on koonnut sen kokonaisuutena, tarkista se, kun saat, jotta voidaan poistaa mahdolliset viat kuljetuksen aikana.
1.Anko biggish -työhön, joten suosittelemme, että leuan murskaimet asentavat betoniharjoitteluun värähtelyjen ja äänien vähentämiseksi, sinun on parempi alustaa lehtipuu temppelit, kuminauhat tai muut tyyny - Eliverateriaalit murskaimien ja betonin perustan välillä.
2.Pohjan paino on noin 5 - 10 kertaa koneen painosta, perustan syvyys on syvempi kuin tämän paikan maan jäätymissyvyys. Koneen asennuksen ja terrajalkojen pulttien sijainti.
3.Mastumassa ennen pistorasian leveyden kokoa, sinun on löydettävä ensin kireä jousi. Ja säätämisen jälkeen säädä jousen kireä aste asianmukaisesti, jotta vaihtamismekanismin estäminen ei toiminut ulkopuolella.
Tuotevideo