Sallama masası
 |
 |
 |
Ürüne Genel Bakış
The beneficiation process of the shaker is carried out on the inclined bed surface with repeated strips. The ore particles are sent from the feed trough at the corner of the bed surface, and the transverse washing water is supplied to the feed trough. Under the action of gravity, the transverse water impulse, the inertia and friction caused by the reciprocating asymmetric movement of the bed surface, the ore particles are stratified according to specific gravity and particle size. The longitudinal motion along the bed surface and the transverse motion along the inclined bed surface are made. Therefore, the ore particles with different specific gravity and particle size gradually fan down in their respective direction of movement, respectively from different areas of theconcentrate end and tailings side, and finally are divided into concentrate, ore and tailings.The outstanding advantage of 6-S shaker is that the separation accuracy is high, and the final concentrate, middle ore and waste tailings can be obtained after a single separation, and multiple products can be obtained at the same time. The concentration ratio of concentrate is high, the sorting efficiency is high, the care is easy, and the stroke is easy to adjust.
Çalışma prensibi
Shaker sorting is realized under the joint action of bed shaking and transverse water flow. Bed bed strips are longitudinal and the direction of water flow is close to vertical. When water flow crosses each bed strip laterally, eddy currents are formed in the groove. The combined action of eddy currents and bed shaking can loosen the mineral sand layer and stratify it according to density. The upper light ore particles are subject to the greater impulse of the water flow, while the lower heavy ore particles are subject to the lesser impulse, so the transverse movement speed of the light ore particles on the bed is greater than that of the heavy ore particles on the bed. This process is called "de lamination".
Uzunlamasına yönde, yatak yüzeyinin ilk başta yavaş bir hızda ve kademeli olarak hızlanırken, ani geri çekilme sırasında hız kademeli olarak azaldığında ve daha sonra ileriye doğru, yukarıdaki işlemi tekrarlayın, aynı zamanda ağır cevher partiküllerinin daha büyük bir hızda ilerlemesini sağlamakla kalmaz, böylece daha büyük bir partiküller ileriye doğru hareket etmekle kalır. Cevher parçacıklarının gittiği yerlerde, uzunlamasına hız ve enine hızın kombinasyonuna bağlıdır. Ağır mineraller daha küçük enine hıza ve daha büyük boyuna hıza sahiptir ve ışık mineralleri daha büyük enine hıza ve daha küçük boyuna hıza sahiptir.
Applying the parallelogram rule to synthesize the longitudinal velocity and transverse velocity, it can be seen that the combined velocity of heavy minerals is inclined to the concentrate end of the shaker, light minerals are inclined to the tailings side of the shaker, and medium density particles are located between the two. This process is called "transport banding".Since the height of the bed is gradually reduced along the longitudinal direction of the self-driving end, the stratified ore particle groups in the groove are continuously stripped off during the movement to the concentrate end.
Olubun üst tabakasındaki ışık mineralleri ilk olarak sıyrılır ve yatak yüzeyinin yatay yönü boyunca atık tarafına taşınır ve ağır mineraller konsantre ucundan boşaltılır. Bu nedenle, tüm yatak yüzeyindeki mineraller, çeşitli ürünler elde etmek için farklı yerçekimine ve farklı parçacık boyutuna göre bir fan dağılımı gösterir.
The concentrate strip is washed by transverse water flow in the smooth area of the bed surface (no bed strip area), so that a few gangue particles mixed in it are washed out, and the grade of the concentrate is further improved.
Ürün videosu